Search This Blog

Sunday, July 31, 2016

Settling In Takes Time

Settling in Takes Time

The delay in posting has been caused by a number of things, Microsoft updates which cause the mouse to sonar deeper than what you click on, multiple clicking in general its been a sore point as it interferes with so much.
Long days which by the time I check emails etc I am tuckered out so have resorted to doing only what is needed.
A few sick days nothing major change to weather, sinus and hay fever slowing everything down. Ah well press on.
The weather of late has been fantastic even the early morning temps of down to 0C and by 10am its 17C+ its not effecting me as it would have down south.  in fact arthritis has eased a whole deal for both of us.
So there is lots to catch up with firstly the Burl which at the moment has taken a back seat. it sat out for days being flattened using a garden pot, potting mix as weight, turned every other day. Finally I could run the electric hand planer over the high/thick spots which took out some tension areas. A few more days before taking it in and clamping it to an MDF board and hand planing it as flat as possible both sides.
It took a few days, its been stored until such time as I can set up the plywood base cut it to shape this will only be to give support and somewhere to secure the frame work of the corner table.
P1090574 P1090578
Prior leaving Sydney I had secured some original Myford accessories through a forum sale the gent was very kind in holding off until we had moved to post them as well as I didn’t have to pay till I had them in my hot little hands.
I scored a Myford Fixed steady rest, Myford Angle Plate, set of original Myford ML7 manuals and booklets. set of Myford Carbide toolingIMG_3940 IMG_3941 IMG_3942 IMG_3943 IMG_3945
All in excellent condition some unused, posted from South Australia the gent who owned them was retiring had sold off the lathe.
Installed a metal hose tidy for Sue. I screwed it onto the wall using plugs and self tapers I’ll give the screws about three years and they’ll need replacing.
20160724_152315 20160724_152538
I have to thanks Sue who took on the task of spraying the old frame on which the Nova 3000 sits. Four cans of Fiddly Bits after a light sand a few days drying time and the Nova is back up and running……..not without drama must always remember the locating swivel pin must be lined up with the locating lock bolt. Still tempted to re-spray the Nova a good clean was all it got. It took the good part of a day to line up level up the beds, some how I ended up with packing washers left over.
20160724_154810 P1090582 P1090586 P1090587 P1090588
Prior the move one of the tool box trolleys had suffered a wonky wheel Ken raced off to buy a new replacement unfortunate as it was it was almost 1/4″ higher then the rest. The floor pan had always caused problems with wheels almost collapsing due to poor reinforcement of  the floor pan area. I bought the remaining three matching new wheels, two strips of zinc plinth bar and removed the rather useless manufacturing packing plates.
P1090467 P1090470 P1090502 P1090504 P1090509 P1090566
It wasn’t until final fitting the size difference was noticed last photo above the matching wheels fitted.
New tool trolley handles made and fitted. Why have the many producers of tool boxes and trolleys stopped fitting sensible easy grab handles? These useless finger grip edge handles even if I was not suffering arthritis in a work environment would drive me round the twist. Oily, greasy hands trying to fumble with no more than a finger tip to open draws full of tools obviously the majority of users work in pristine environments.
P1090464 P1090472 P1090473
Sue had a bookcase which required a centre partition due to distance between supports being to large. Yes i made it but I was following directions of design originally. A woman is always allowed to change her mind. Anyway we now share the bookcase, we need another.
I had to of course drill the holes required for shelf support pins.
Sue lacquered the new shelves and partition addition.
P1090570 P1090572
One side of the workshop is taking form and is quit workable, note flooring has been laid again checker plate workshop vinyl. A new storage shelf for the Myford frame and cover. old pantry now storage for finishes and unfinished projects hanging space for squares and rulers.
P1090595 P1090596 P1090597
Last photo above taken about 3.30pm as sun begins to set with that I’ll leave this and go post another this time on Sue who has been helping me do much of this above.

No comments:

Post a Comment

Your comments are welcome please forgive us if not replied to immediately.